Thermador Range Burner Not Lighting in Las Vegas
The five-pointed flame will not catch, one point stays dark, or the igniter keeps snapping long after dinner is going. Thermador's pointed burner is a different design from most round gas burners, and so are the reasons it stops lighting.
Other brands: $89.
- Your choice: pay online now or when the tech arrives.
Extra appliance on the same visit+$49
Need it tonight or this weekend? Call (702) 846-1004. After-hours visits $149 weeknights (5–9 PM), $139 weekends, credited toward the repair.
- 1,000+ jobs completed
- 100% satisfaction promise
- Same-day service available
- 90-day labor guarantee
Why won't my Thermador burner light?
Thermador's five-pointed burner spreads flame across more ports than a round burner, so a partly blocked port or a cap sitting a few degrees off can stop it from lighting or leave gaps in the flame. Add the igniter, the knob switch, the spark module and the ExtraLow simmer system on many models, and that covers almost every call. The $179 diagnostic finds the real cause and comes off the repair if you go ahead.
- Thermador Pro Grand, Pro Harmony and gas rangetops
- Five-pointed burners and ExtraLow simmer burners
- One flat price before any work starts
- Independent service, not affiliated with Thermador
What a Thermador Burner That Won't Light Usually Means
The five-pointed burner is Thermador's signature: a sealed head with ports running around every point, topped by a matching cap. The shape spreads heat to the edge of the pan, but it also means more ports, more edges and a cap that only works when it is seated exactly. Below the cooktop, a spark module and a switch at each knob handle ignition, and ExtraLow burners add a control that cycles the flame on purpose.
Cap alignment and port blockage
If the pointed cap is rotated even slightly off its base, gas escapes in the wrong pattern and the igniter cannot reach it. Spills that dry in the valleys between the points, plus mineral scale from hard Las Vegas water and dust that settles on a cooktop in a dry climate, choke the ports one by one. The result is a burner that lights only part of the way around, or not at all.
Igniter and the spark path
Each pointed burner has an igniter next to its base. A cracked porcelain body, a crusted tip or moisture from a boilover lets the spark leak to the wrong spot instead of jumping to the burner. You hear normal clicking, but the gas never catches. A loose or damaged igniter wire under the cooktop gives the same result.
ExtraLow simmer cycling
On Thermador burners with ExtraLow, the lowest settings work by turning the flame off and back on in a timed cycle. A burner that goes out and relights by itself on those settings is doing what it was designed to do. When the cycle stops relighting, or the burner will not stay lit on any setting, the ExtraLow valve or control and the reignition circuit are where our tech looks.
Spark module and knob switches
One spark module drives all of the igniters. A weak module makes every burner slow to light. Switches at each knob tell the module when to fire, and a spill or worn contacts can leave one switch stuck closed, so the igniters snap without end. Power dips during summer storms in the valley are a common trigger for module and switch faults.
Signs That Come With It
Thermador owners usually call us with one of these:
- Igniter snaps but the burner never catches
- Flame lights on some points of the burner and not others
- Clicking keeps going with every burner off
- Simmer burner goes out and does not come back
- Burner lights on high but dies when turned down
- Yellow, lifting or uneven flame after a spill
- All burners slow to light at the same time
- No spark from any burner after a power outage
What Our Tech Checks
On a Thermador ignition call our tech works through the burner from the top down:
- Pointed cap fit, rotation and seating on its base
- Port condition around every point of the burner head
- Igniter porcelain, tip and spark gap
- Igniter wiring under the cooktop
- Spark module output and each knob switch
- ExtraLow cycling and reignition behavior on simmer
You hear the cause in plain words with one flat price before any part goes in. If the burner is actually doing a normal ExtraLow cycle, our tech will say that too, and you will not pay for a repair the range does not need.
Is a Thermador Range Worth Repairing?
Yes, in nearly every case. A Thermador pro range or rangetop is a big investment, and igniters, switches, spark modules and burner parts are small next to the cost of a comparable new range plus installation and any hood or cabinet changes it brings. A burner that will not light does not mean the range is worn out.
Where it gets closer: an older Thermador that also has oven heating problems, a failing control panel and worn gas valves. In that case our tech prices every repair together, and the total gets compared honestly against replacing the range.
What It Costs
| Thermador diagnostic visit | Tech finds the cause and gives you one flat price. Comes off the repair if you go ahead. | $179 |
|---|---|---|
| Extra appliance, same visit | Have a second appliance looked at while we are there. | +$49 |
| Typical range repair | Burner heads and caps, igniters, knob switches, spark module or simmer controls. | $250 to $750 + parts |
Thermador ignition repairs depend on whether the fault is at the burner, the igniter, the switch or the module. Your exact price is set after the $179 diagnostic, before any work.
Nothing to pay to book. Pay online now or when the tech arrives, your choice. The $179 diagnostic comes off the repair if you go ahead, and you approve one flat price before any work starts.
Fixed Right or We Come Back Free. If the same problem comes back within 90 days of our repair, call us and we come back and fix it at no charge. We need the chance to come back first: if another company works on the appliance before we return, the guarantee no longer applies. Parts carry the manufacturer's warranty.
Thermador Burner Not Lighting FAQ
Why does my Thermador burner shut off and relight on its own?
On ExtraLow settings that is normal. Thermador cycles the flame off and on to hold a very low simmer. If it does this on higher settings, or does not relight, the simmer control or reignition circuit needs a look.
Why is my Thermador igniter clicking with the burners off?
A knob switch is usually stuck closed, often from moisture or a spill reaching it, so the spark module keeps firing. Less often the spark module itself has failed. Our tech tests each switch to find the one at fault.
How much does Thermador burner repair cost?
The diagnostic is $179 and comes off the repair if you go ahead. Typical repairs run $250 to $750 in labor plus parts, depending on the appliance and repair time. You approve one flat price before any work starts.
Are you a Thermador service center?
No. Tuffix Pro is an independent repair service, not affiliated with Thermador or BSH Home Appliances.
Why does only part of my Thermador burner light?
Usually the pointed cap is slightly rotated or some ports around the points are blocked by dried spills or scale. Gas then flows unevenly and the flame skips those points.
Related Repair Pages
Where we work
Our tech services Thermador ranges and rangetops in Green Valley, Seven Hills, Inspirada and Spring Valley, and across the wider Las Vegas and Henderson area.
Independent service. Not affiliated with BSH Home Appliances. Thermador is a trademark of its owner.
Thermador Burner Dark? Get It Lit Again.
Nothing to pay to book. The $179 diagnostic comes off the repair.
Calling? Mention code THR-IGN so we know which page you found us on.